How To Install Tin Ceiling Tiles On Your House
About the Author:
#end
How To Install Tin Ceiling Tiles On Your House
Article Source: http://myblogi.tumblr.com/post/59777627908
One of the hardest balancing acts that many home owners must face every day is the cost vs durability and cost on planned home improvements. Most owners know that having tin ceiling tiles can add a contemporary beauty to their home. While older tiles are believed to have much better craftsmanship than new ones, most mass produced tiles are quite inexpensive and also easy to install on any home.
The classic tin ceiling is making a comeback in many modern homes built today. The classic tiles from remodeled homes are now selling at an a substantially higher price than when they were new. Many owners find they have good luck getting new panels then self installing them. Installing new ones and old ones generally follow the same procedure from start to end.
It is often best to seal the ceiling up with a quality primer and always let it completely dry. Plywood is then nailed and screwed to it forming a base for your tiles. Some times lathing may be used, though plywood is considered to have better holding power on the ceiling. Its critical to ensure the whole roof is covered up and the plywood is only attached to the joists not the drywall.
One of the biggest differences between a good looking job and a poor looking one is whether the panels are sitting square to each other and the center line of the room. Few rooms are made as a square so it is best to mark out the center of the room and make a center line down the middle for reference. Make sure you can see the line well because this is the starting point for all your panels.
After the center line is done you are ready to install the cornice. Most cornices will have slightly flanged edge along the side. This is typically the side that will be covered by the roof panels. The flanged edge is nailed to your plywood. Some newer cornices will also use a long aluminum strip that is nailed to the wall to help with supporting them.
It is typically a good plan to lay out your new panels on the ground before you begin attaching them to your ceiling. This can give you a picture of how the panels will appear so you can adjust them for a perfect layout. It is easier in any case to transfer your panels off the floor to to your roof.
When you begin transferring your panels from floor to roof, try using tacking nails to connect them. These tacking nails are longer than a normal nail and can be easily removed with hand pliers if you make any mistakes. When everything is placed where you like it, you can then systematically return to use shorter finish nails for attaching them.
Work from your center line to the edge. Take time to ensure any of the laps will face away from the doorways so they will be less noticeable. When you have completed this, install the border pieces and any light fixtures or other accessories you may have left. Now enjoy the tin ceiling tiles you have installed.
The classic tin ceiling is making a comeback in many modern homes built today. The classic tiles from remodeled homes are now selling at an a substantially higher price than when they were new. Many owners find they have good luck getting new panels then self installing them. Installing new ones and old ones generally follow the same procedure from start to end.
It is often best to seal the ceiling up with a quality primer and always let it completely dry. Plywood is then nailed and screwed to it forming a base for your tiles. Some times lathing may be used, though plywood is considered to have better holding power on the ceiling. Its critical to ensure the whole roof is covered up and the plywood is only attached to the joists not the drywall.
One of the biggest differences between a good looking job and a poor looking one is whether the panels are sitting square to each other and the center line of the room. Few rooms are made as a square so it is best to mark out the center of the room and make a center line down the middle for reference. Make sure you can see the line well because this is the starting point for all your panels.
After the center line is done you are ready to install the cornice. Most cornices will have slightly flanged edge along the side. This is typically the side that will be covered by the roof panels. The flanged edge is nailed to your plywood. Some newer cornices will also use a long aluminum strip that is nailed to the wall to help with supporting them.
It is typically a good plan to lay out your new panels on the ground before you begin attaching them to your ceiling. This can give you a picture of how the panels will appear so you can adjust them for a perfect layout. It is easier in any case to transfer your panels off the floor to to your roof.
When you begin transferring your panels from floor to roof, try using tacking nails to connect them. These tacking nails are longer than a normal nail and can be easily removed with hand pliers if you make any mistakes. When everything is placed where you like it, you can then systematically return to use shorter finish nails for attaching them.
Work from your center line to the edge. Take time to ensure any of the laps will face away from the doorways so they will be less noticeable. When you have completed this, install the border pieces and any light fixtures or other accessories you may have left. Now enjoy the tin ceiling tiles you have installed.
About the Author:
Read more about How To Install Tin Ceiling Tiles On Your House visiting our website.
#end
How To Install Tin Ceiling Tiles On Your House
Article Source: http://myblogi.tumblr.com/post/59777627908
No comments:
Post a Comment